11 operating steps for a microscope
1. Vị trí vị trí của sinh học kính hiển vi nên be in a khô và sạch phòng đến tránh khuôn trên quang học thành phần% 2c rỉ sét on kim loại bộ phận% 2c và bụi tích tụ. Sau sử dụng kính hiển vi, ngay lập tức đặt nó trở lại vào hộp hộp (tủ)% 2c hoặc nắp nó với a thủy tinh hoặc nhựa vỏ bọc 2c và đặt in sấy khô tác nhân.
2. Do not disassemble the components of the biological microscope by yourself; The lens tube should be inserted with a contact lens or a protective cover to prevent dust from entering from of lens tube; Do not touch or wipe the surface of the lens with your fingers. If there is dust, gently brush it off with a soft brush and then use a soft cleaning vải đến lau nó. Bạn có thể cũng sử dụng ống kính lau giấy nhúng in a nhỏ xylene hoặc dầu mỏ đến thử lau, nhưng hãy cẩn thận không đến vẽ sọc trên bề mặt bề mặt của ống kính khuôn trên ống kính và không thể be lau tắt với lau giấy, a bông tăm bông nhúng in a nhỏ hỗn hợp của 70% 25 ethanol và 30% 25 acetaminophen can be nhẹ nhàng lau.
3. Sinh học kính hiển vi nên không được đặt cùng nhau với ăn mòn axit% 2c hạ cấp hoặc cao dễ bay hơi hóa chất đến ngăn chặn ăn mòn và rút ngắn của họ dịch vụ cuộc sống. Trong nguyên tắc% 2c quan sát mẫu vật chứa chất lỏng, it is nói chung cần thiết đến che phủ chúng với a nắp thủy tinh% 3b if the chất lỏng chứa ăn mòn hóa chất như vậy as axit và bazơ% 2c các cạnh của nắp thủy tinh nên được niêm phong với parafin hoặc Vaseline và sau đó quan sát. Tuy nhiên, do to the frequent use of such reagents during inco microscopic identification of phồn thể Trung Quốc medicine, it is not possible to seal them all. Do đó, special care should be taken to prevent liquid from flowing onto the stage and not touching the objective lens.
4. Sinh học kính hiển vi nên không được tiếp xúc đến trực tiếp ánh sáng mặt trời% 2c nor nên nó được đặt gần bếp hoặc sưởi ấm đến tránh quá mức thay đổi trong nhiệt độ đó có thể nguyên nhân tách rời% 2c hoặc thiệt hại đến ống kính và thành phần.
5. Làm sạch sinh học kính hiển vi mục tiêu chỉ trên bên ngoài bề mặt. Sau tiếp xúc bề mặt là bị ô nhiễm với thuốc% 2c sử dụng a gương giấy nhúng in a nhỏ lượng của lau lau dung dịch để lau nó (làm không sử dụng ethanol)% 3b If the back cần to be làm sạch, a mềm bàn chải can be used to lau it off, or a da hút đầu can be used to remove bụi.
6. Khi điều chỉnh độ dày và lấy nét tỷ lệ của nhôm, the action nên be chậm và không nghiền nắp tấm đến ngăn chặn thiệt hại đến mục tiêu ống kính và bộ sưu tập due đến kiểm soát tác động.
7. Sau khi sử dụng the oil lens, it is necessary to lau off the cedar oil on the lens (you can use lens lauping paper dipped in a little xylene to wipe it off, but note that xylene cannot peinrate into the inside of the lens, else xylene will dissolve the adhesive between the lenses and cause the lens to fall off).
8. The Mirror surface of the reflector should be protected and cleaned to prevent water, xylene, or cedar oil from penetrating, in order to prevent the mercury from falling off the reflector.
9. If the mechanical part is not flexible, you can use a fine silk cloth dipped in xylene to wipe off rust and grease (do not use ethanol, as these solvents will corrode the paint), and then lubricate with a little liquid stone cloth; Do not forcefully twist it too tightly to avoid damage.
10. Sometimes stains or foreign objects are found in the field of view of a biological microscope, and the eyepiece can be rotated first. If these stains rotate along with it, it can be determined that the stains are on the eyepiece; Otherwise, the specimen can be moved, and if the stain moves with it, the stain is on the specimen. If neither is true, then the stain is on the objective lens. You can first pick up the front lens of the food lens and then check the back lens. Clean according to the situation.
Đôi khi a phần của the field of view is unclear, which may be due to fingerprints or dust on the surface of the front lens of the objective or eyepiece, or it may be due to poor specimen preparation or improper use of the microscope, such as poorly adjusted lighting systems. The situation should be identified and resolved private.
11. Sau khi sử dụng sinh học kính hiển vi, tất cả bộ phận nên be lau sạch, the grid mục tiêu nên được quay vào an bát giác hình dạng% 2c the ống kính ống và bộ sưu tập nên được hạ xuống và gương bề mặt của gương của gương phản xạ nên be đặt in a dọc vị trí.
